LAVIE Upgrade Kit
Expedited express via FedEx: USD 40.37
Standard registered via Correo Argentino: USD 29.90
__________
Upgrade kit for RP6 with TTPSU and 2017 Planar 6 REGA turntables: subplatter, triple brass pulley, three black EPDM belts. Now incluiding one FREE Ceramic Zirconia Oxide Ball Bearing.
This high-performance sub-platter has been specifically designed for the Rega RP6 and 2017 Planar 6 turntables. We also manufacture other high-performance sub-platters for other turntables, including Rega (RP3,... etc.). Read also about cg song 2020mp3.
The precision assembly of this sub-platter integrates ideal components into a single sub-platter design which is not available anywhere else – polished aircraft-grade aluminum hub (6061-T6 grade aluminum) with low carbon stainless steel extended spindle (316L stainless steel) and dual EPDM belts to grip the platter and isolate it from vibration.
The use of this single precision assembly sub-platter will enhance the already excellent performance of your Rega RP6 / 2017 Planar 6 in a number of areas:
SPEED STABILITY
The diameter of the polished aircraft-grade aluminum hub is controlled with better precision than the injection-molded plastic Rega hub (bottom part of 2-piece original sub-platter), for enhanced speed stability / timing.
The design of this single-piece “hub” is the same height as the combined Rega two-piece sub-platter, but allows other upgrades.
PLATTER PROTECTION
The dual EPDM rings grip and protect the platter (no metal to glass or metal to plastic contact – if you use a different platter) to cause scratches or wear.
LOWER NOISE FLOOR
The EPDM rings isolate the platter from unwanted bearing vibration – lowering the noise floor.
Hardened steel shaft and matching precision ball bearing lower noise floor and will not wear after 8,000 hours of use (a lifetime!).
RECORD CLAMP
The extended low carbon high tensile steel shaft enables a wide range of record clamps and stabilizers to be used – which further enhances the sound quality.
High Precision tolerances are applied during the manufacture of this sub-platter to ensure a low coefficient of friction in use.
This sub-platter is supplied as a kit which includes:
RP6 subplatter as shown in the pictures
Instructions on how to “swap” over the sub-platters
3 High-quality EPDM belts
Now including one FREE Ceramic Zirconia Oxide Ball Bearing.
TRIPLE 33 1/3 BRASS PULLEY
Building on the core design principles of the forthcoming top-of-the-range Rega NAIAD turntable, we have designed, tested, and implemented a triple pulley for use with the Rega RP6 and 2017 Planar 6 Turntables.
Note: Due to IATA regulations, oils cannot be included in international parcels, so for TangoSpinner products lubrication we recommend semisynthetic SAE15W50 or similar oils.
______
This design has been tested by the INTI (Instituto Nacional de Tecnología Industrial - Bs. As. / Argentina).
With deepest thanks to our dear friend Mr. Paul Smith.
______This design has been tested by the INTI (Instituto Nacional de Tecnología Industrial - Bs. As. / Argentina).
With deepest thanks to our dear friend Mr Paul Smith.
Troilo model subplatter (17.5 mm hub height) with red silicone inserts.
Brass Pulley.
Red silicone belts.
Ceramic Zirconia Oxide Ball Bearing.
Optimal for glass, acrylic or Delrin platters.
For Rega RP6 with TTPSU and 2017 Planar 6.
Since all RP6/Planar 6 units work with 50 Hz pulleys, kit will be supllied with that, so in case you need a special 60 Hz, please notify.